地埋示踪线于对相关管道的探测、追踪及定位，一般会采用金属线芯，通过探测设备给金属线施加信号，由探测接收机接收信号，从而找到示踪线的准确位置，即同步追踪到管道的具体位置；以便于对管道进行改造及维修。下面来讲讲地埋示踪线安装连接的操作说明内容吧。

The buried tracer line is used to detect, track and locate the relevant pipeline. Generally, the metal wire core is used to apply signals to the metal wire through the detection equipment, and the detection receiver receives the signals, so as to find the accurate position of the tracer line, that is, synchronously track to the specific position of the pipeline; So as to facilitate the reconstruction and maintenance of the pipeline. Let's talk about the operating instructions for the installation and connection of buried tracer lines.

产品用途：用于埋地塑料管道的探测及示踪。

Application: used for detecting and tracing buried plastic pipelines.

适用范围：燃气埋地PE管道、供水埋地PE、PVC管道、及非金属埋地管道。

Scope of application: gas buried PE pipeline, water supply buried PE, PVC pipeline, and non-metallic buried pipeline.

安装零部件及工具

Installation parts and tools

1、所有物品

1. All items

2、连接夹/防水(腐)连接器

2. Connecting clip / waterproof (corrosion) connector

3、工具

3. Tools

操作步骤：直线连接

Operation steps: straight line connection

用剪钳剪断示踪线--剪刀剪开两条示踪线--剥去PE外保护皮--穿入防腐/防水连接器--金属丝穿入蓝色接线柱内--用夹钳将连接夹夹紧--确认接口处连接牢固--将防腐/防水连接器紧固

Cut off the trace line with scissors -- cut off two trace lines with scissors -- strip the PE outer protective skin -- thread into the anti-corrosion / waterproof connector -- thread the metal wire into the blue terminal -- clamp the connecting clamp with pliers -- confirm that the connection at the interface is firm -- tighten the anti-corrosion / waterproof connector

操作步骤：三通连接

Operating steps: tee connection

更换成黑色双孔胶头--将三条线穿入防水接头--金属丝穿入黄色接线柱后夹紧--紧固防腐/防水连接器

Replace with black double hole rubber head -- thread the three wires into the waterproof connector -- thread the metal wire into the Yellow terminal and clamp it -- tighten the anti-corrosion / waterproof connector

按照操作说明要求施工：

Construction in accordance with the operating instructions:

1、用剪刀剪开（分离）两条并联的示踪线时，应注意两条线是否均匀，被分开的两条示踪线表面要光滑，不能有凸台、尖角（非常重要），会影响连接器的防水性能。

1. When cutting (separating) two parallel trace lines with scissors, pay attention to whether the two lines are uniform. The surface of the separated two trace lines should be smooth without bosses and sharp corners (very important), which will affect the waterproof performance of the connector.

2、是否有金属线漏出，不能将外漏金属丝的示踪线埋地。

2. Whether there is any metal wire leakage, the tracer line of the leaked metal wire shall not be buried.

3、在剥PE保护层时不要损伤金属线。

3. Do not damage the metal wire when stripping the PE protective layer.

4、接线柱连接好接头后，应用力拉动接头两端的示踪线，检查接头的连接强度。

4. After the terminal is connected to the joint, the tracer wires at both ends of the joint shall be pulled to check the connection strength of the joint.

5、不要忘记对防腐/防水连接器的紧固；出地后的示踪线头部位，应用防水胶布和热缩管封紧。

5. Do not forget to fasten the anti-corrosion / waterproof connector; After leaving the ground, the tracer thread head shall be sealed with waterproof tape and heat shrinkable pipe.

6、地埋示踪线应在每个阀门井处设置接头便于检测，每五百米必须设置一个检测井。

6. The buried tracer line shall be provided with joints at each valve well for inspection, and one inspection well must be provided every 500m.

以上就是问题解答的相关内容了，希望能够帮助到大家，如对这一问题还存在任何疑问，都欢迎关注我们网站http://www.binzhouhengtong.com并咨询我们的工作人员，将竭诚为您服务。

The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.binzhouhengtong.com And consult our staff, will serve you wholeheartedly.