燃气警示带在我们的生活中所起到的就是警示作用，以确保周围人员的人身。在禁止人们进入的地方，防止“非内部人员禁止入内”的警示带，可以保证内部器械的以及外来人员的等等。

Gas warning tape plays a warning role in our life to ensure the personal safety of people around. In places where people are not allowed to enter, the warning tape preventing "non internal personnel are not allowed to enter" can ensure the safety of internal equipment and the safety of external personnel.

燃气警示带主要是由燃气警示带盒子、摇表、警示带、调节钮、金属卡片构成的。燃气警示带主要是用于户外及室内的敞开式高压场所的工作，或者是临时隔离邻近的运行设备。

Gas warning tape is mainly composed of gas warning tape box, megger, warning tape, adjusting knob and metal card. Gas warning tape is mainly used for outdoor and indoor work in open high-voltage places, or for temporary isolation of adjacent operating equipment.

技术要求警示带的宽度在5㎝左右，并在带上印有“止步，高压危险”等字样，字样间隔为一米。警示带的长度要根据实际的使用情况来进行设计，一般为20米/盘，30米/盘，50米/盘。

The width of the warning tape shall be about 5 cm, and the tape shall be printed with words such as "stop, high pressure danger", with an interval of one meter. The length of the warning tape shall be designed according to the actual use, generally 20 m/plate, 30 m/plate and 50 m/plate.

在每一盘已经出厂的警示带上都应有长久性的明显标志;并印有警示带的名称和规格，以及制造厂名和型号，包括主要性能等都需要明显的标注出来。并且在盘上还需要注上制造日期。

Each warning tape that has been delivered shall be marked with permanent and obvious signs; The name and specification of the warning tape, as well as the name and model of the manufacturer, including the main performance, should be clearly marked. And the date of manufacture shall also be marked on the plate.

燃气警示带如何使用

How to use gas warning tape

1、检查是否预留出了信号接入点，安装方式是否正确。

1. Check whether the signal access point is reserved and whether the installation method is correct.

2、检查警示带中的导电金属丝是不是可以加载探测信号，有没有信号泄漏的情况出现，以及是否设置了足够的信号检测井；

2. Check whether the conductive metal wire in the warning tape can load the detection signal, whether there is signal leakage, and whether there are enough signal detection wells;

3、示踪警示带安装好了之后，始端和末端是不是与地面隔离，信号检测井内的警示带是否进行了固定处理；

3. After the tracer warning tape is installed, whether the start and end are isolated from the ground, and whether the warning tape in the signal detection well is fixed;

4、可探测警示带中的导电金属丝的直径是不是满足应用要求，金属丝直径太小容易被拉断，直径太大则会导致探测信号误差增大，应该选取综合效果好的直径。探测信号容易出现的主要问题是信号连续性易受影响。原因有多种：

4. Whether the diameter of the conductive metal wire in the detectable warning tape meets the application requirements. If the diameter of the metal wire is too small, it is easy to break. If the diameter is too large, it will lead to increased detection signal error. Therefore, the diameter with good comprehensive effect should be selected. The main problem of detection signal is that the signal continuity is easily affected. There are many reasons:

①可能在施工过程中操作失误导致了警示带内部的导线断裂，造成了检测短路；②警示带的绝缘以及防水处理不够过关，导致电线受潮影响探测；③导电金属丝的直径过大，造成电阻增大，信号衰减增大，影响探测的效果。

① It is possible that the wire inside the warning tape was broken due to the operation error during the construction, resulting in the detection short circuit; ② The insulation and waterproof treatment of the warning tape are not up to standard, which causes the wire to be affected by moisture and affects the detection; ③ The diameter of the conductive metal wire is too large, which causes the resistance to increase and the signal attenuation to increase, affecting the detection effect.

燃气警示带的标注以及使用方法已经在上述内容中讲解到了，那么您对此有新的理解了吗？您有相关的问题或需求都能来我们网站http://www.binzhouhengtong.com进行咨询！

The marking and use method of gas warning tape have been explained in the above contents. Do you have a new understanding of this? You can come to our website if you have relevant questions or needs http://www.binzhouhengtong.com Consult!